RENU™ PEEK LF NAT-MP### provides the same flexible custom mesh sizing as TDS-003 in the low-flow PEEK grade. Milled from clean post-industrial low-viscosity PEEK scrap, this product covers mesh sizes from 20 to 170 mesh and is selected for applications where controlled melt flow during processing is important, combined with a non-standard particle size distribution. Ideal for compression molding of complex geometries, thermal spray with lower-energy systems, and research applications requiring specific particle size ranges.
PHYSICAL PROPERTIES
Property | Value / Range |
Polymer Type | Polyetheretherketone (PEEK) |
Flow Grade | Low Flow (LF) |
RENU™ Code | RENU™ PEEK LF NAT-MP### (### = mesh size) |
Color | Natural (off-white to light tan) |
Available Mesh Range | 20 to 170 mesh (custom to order) |
Particle Shape | Irregular (ambient milled) |
Bulk Density (loose) | 0.40–0.65 g/cm³ (varies by mesh) |
Moisture Content | < 0.05% (as-shipped) |
THERMAL PROPERTIES
Property | Value |
Glass Transition Temperature (Tg) | 143°C (289°F) |
Melting Point (Tm) | 343°C (649°F) |
Continuous Use Temperature | 250°C (482°F) |
Thermal Conductivity | 0.25 W/m·K |
MECHANICAL PROPERTIES
Property | Value (SI) | Value (Imperial) |
Tensile Strength | 100 MPa | 14,500 psi |
Flexural Strength | 165 MPa | 24,000 psi |
Compressive Strength | 120 MPa | 17,400 psi |
CHEMICAL RESISTANCE
Agent / Environment | Resistance Rating |
Strong Mineral Acids (H₂SO₄, HCl, HNO₃) | Good — consult for concentrated applications |
Weak Acids | Excellent |
Strong Alkalis / Bases | Good |
Weak Alkalis / Bases | Excellent |
Aliphatic Hydrocarbons | Excellent |
Aromatic Hydrocarbons | Excellent |
Halogenated Solvents | Excellent |
Ketones & Esters | Excellent |
Alcohols | Excellent |
Hot Water / Steam (to 200°C) | Excellent |
Fuels & Oils | Excellent |
Water Absorption (24 hr, ASTM D570) | < 0.5% |
TYPICAL APPLICATIONS
Note: RENU™ recycled powders are suitable for non-critical industrial, electronics, automotive, and commercial applications. They are NOT recommended for safety-critical aerospace structures or life-sustaining medical devices.
Application Area | Specific Uses |
Compression Molding (Large Parts) | Coarser LF grades preferred for large tooling where finer powders compact unevenly |
Thermal Spray (Low-Energy Systems) | LF grade coarser powders for lower-energy spray systems with larger nozzle orifices |
R&D Applications | Laboratory work requiring specific particle size ranges in lower-flow PEEK |
PACKAGING & AVAILABILITY
Format | Details |
Box (Standard) | Up to 25 kg (55 lbs) per box — double-wall corrugated with poly liner |
Drum (Bulk) | 68 kg (150 lbs) bulk drums — fiber or plastic drum with sealed poly liner |
Custom Packaging | Available on request for larger volumes — contact PolyClean for details |
Labeling | Each container labeled with: RENU™ product code, mesh size, lot number, and date of manufacture |
Processing Notes See TDS-003 for complete mesh size conversion chart. LF grade is preferred over HF where flash or bleed at parting lines is a concern in compression molding. |
DISCLAIMER The technical data contained in this document has not been produced by PolyClean Technologies through its own independent testing and measurements. This information has been assembled from publicly available data published by original polymer manufacturers and industry reference sources. PolyClean Technologies makes no warranties, expressed or implied, regarding the accuracy or completeness of this information. Customers are solely responsible for verifying that this material is suitable for their specific application. PolyClean Technologies shall not be liable for any damages resulting from the use of this information or from the use of its products in any application. This data is intended for general guidance only. RENU™ recycled materials are produced from post-industrial clean scrap and are appropriate for non-critical industrial, commercial, electronics, and general-purpose applications. They are not recommended or warranted for use in flight-critical aerospace structures, implantable medical devices, or other life-safety applications without thorough independent testing and qualification by the end user. |
RENU™ PEEK HF NAT-MP### is PolyClean’s custom-mesh version of the high-flow PEEK powder line. Produced from the same clean, post-industrial recycled PEEK feedstock as TDS-001, this product is precision-milled and sieved to customer-specified mesh sizes across the range of 20 to 170 mesh (approximately 850 µm to 90 µm top particle size). Custom mesh cuts are available for applications where standard 140-mesh particle size distributions are too fine or too coarse. Minimum order quantities apply — contact PolyClean for pricing and lead times.
PHYSICAL PROPERTIES
Property | Value / Range |
Polymer Type | Polyetheretherketone (PEEK) |
Flow Grade | High Flow (HF) |
RENU™ Code | RENU™ PEEK HF NAT-MP### (### = sieve mesh size) |
Color | Natural (off-white to light tan) |
Available Mesh Range (US Std) | 20 mesh to 170 mesh (custom to order) |
20 Mesh top size | ≤ 850 µm |
40 Mesh top size | ≤ 425 µm |
80 Mesh top size | ≤ 177 µm |
140 Mesh top size | ≤ 105 µm |
170 Mesh top size | ≤ 90 µm |
Particle Shape | Irregular (ambient milled) |
Bulk Density (loose) | 0.40–0.65 g/cm³ (varies by mesh) |
Moisture Content | < 0.05% (as-shipped) |
THERMAL PROPERTIES
Property | Value |
Glass Transition Temperature (Tg) | 143°C (289°F) |
Melting Point (Tm) | 343°C (649°F) |
Continuous Use Temperature | 250°C (482°F) |
Thermal Conductivity | 0.25 W/m·K |
CTE | 47 × 10⁻⁶ /°C |
MECHANICAL PROPERTIES
Property | Value (SI) | Value (Imperial) |
Tensile Strength | 100 MPa | 14,500 psi |
Flexural Strength | 165 MPa | 24,000 psi |
Compressive Strength | 120 MPa | 17,400 psi |
Izod Impact (Notched) | 85 J/m | 1.6 ft-lb/in |
CHEMICAL RESISTANCE
Agent / Environment | Resistance Rating |
Strong Mineral Acids (H₂SO₄, HCl, HNO₃) | Good — consult for concentrated applications |
Weak Acids | Excellent |
Strong Alkalis / Bases | Good |
Weak Alkalis / Bases | Excellent |
Aliphatic Hydrocarbons | Excellent |
Aromatic Hydrocarbons | Excellent |
Halogenated Solvents | Excellent |
Ketones & Esters | Excellent |
Alcohols | Excellent |
Hot Water / Steam (to 200°C) | Excellent |
Fuels & Oils | Excellent |
Water Absorption (24 hr, ASTM D570) | < 0.5% |
ELECTRICAL PROPERTIES
Property | Value |
Volume Resistivity | > 10¹⁶ Ω·cm |
Dielectric Constant (1 MHz) | 3.2 |
TYPICAL APPLICATIONS
Note: RENU™ recycled powders are suitable for non-critical industrial, electronics, automotive, and commercial applications. They are NOT recommended for safety-critical aerospace structures or life-sustaining medical devices.
Application Area | Specific Uses |
Thermal Spray | Coarser mesh grades (20–60 mesh) preferred for flame and plasma spray coating systems |
Fluidized-Bed Coating | Medium mesh grades (40–80 mesh) for fluidized-bed powder coating processes |
Compression Molding | All mesh sizes applicable — coarser particles may improve flow in large tool geometries |
Composite Filler | Custom fines used as polymer filler in composite formulations |
R&D / Testing | Custom particle sizes for laboratory qualification and process development work |
PACKAGING & AVAILABILITY
Format | Details |
Box (Standard) | Up to 25 kg (55 lbs) per box — double-wall corrugated with poly liner |
Drum (Bulk) | 68 kg (150 lbs) bulk drums — fiber or plastic drum with sealed poly liner |
Custom Packaging | Available on request for larger volumes — contact PolyClean for details |
Labeling | Each container labeled with: RENU™ product code, mesh size, lot number, and date of manufacture |
Processing Notes Specify target mesh size on purchase order (e.g., RENU™ PEEK HF NAT-MP080 for 80-mesh). Custom mesh orders may have longer lead times than standard 140-mesh stock. Particle size distributions (PSD reports) available upon request for qualified customers. Minimum order quantities apply for non-standard mesh sizes — contact PolyClean. |
DISCLAIMER The technical data contained in this document has not been produced by PolyClean Technologies through its own independent testing and measurements. This information has been assembled from publicly available data published by original polymer manufacturers and industry reference sources. PolyClean Technologies makes no warranties, expressed or implied, regarding the accuracy or completeness of this information. Customers are solely responsible for verifying that this material is suitable for their specific application. PolyClean Technologies shall not be liable for any damages resulting from the use of this information or from the use of its products in any application. This data is intended for general guidance only. RENU™ recycled materials are produced from post-industrial clean scrap and are appropriate for non-critical industrial, commercial, electronics, and general-purpose applications. They are not recommended or warranted for use in flight-critical aerospace structures, implantable medical devices, or other life-safety applications without thorough independent testing and qualification by the end user. |
RENU™ PEEK LF NAT-MP140 is a precision-milled, low-flow grade PEEK powder derived from clean post-industrial recycled polyetheretherketone. The low-flow (LF) designation reflects feedstock derived from lower-viscosity PEEK scrap, yielding a powder with slightly different melt-flow characteristics while retaining excellent structural and thermal properties. The 140-mesh particle cut is suited for compression molding, press-and-sinter operations, and demanding powder coating applications where a more controlled flow during processing is preferred. Properties closely approximate virgin PEEK LF at significantly reduced material cost.
PHYSICAL PROPERTIES
Property | Value / Range |
Polymer Type | Polyetheretherketone (PEEK) |
Flow Grade | Low Flow (LF) |
RENU™ Code | RENU™ PEEK LF NAT-MP140 |
Color | Natural (off-white to light tan) |
Mesh Size (US Standard Sieve) | 140 mesh |
Nominal Top Particle Size | ≤ 105 µm |
D50 Particle Size (typical) | 40–65 µm |
Particle Shape | Irregular (ambient milled) |
Bulk Density (loose) | 0.45–0.60 g/cm³ |
Apparent / Tap Density | 0.65–0.80 g/cm³ |
Moisture Content | < 0.05% (as-shipped) |
THERMAL PROPERTIES
Property | Value |
Glass Transition Temperature (Tg) | 143°C (289°F) |
Melting Point (Tm) | 343°C (649°F) |
Continuous Use Temperature | 250°C (482°F) |
Short-Term Peak Temperature | 310°C (590°F) |
Thermal Conductivity | 0.25 W/m·K |
Coefficient of Thermal Expansion (CTE) | 47 × 10⁻⁶ /°C |
Heat Deflection Temperature (1.8 MPa) | 152°C (306°F) |
MECHANICAL PROPERTIES
Property | Value (SI) | Value (Imperial) |
Tensile Strength | 100 MPa | 14,500 psi |
Tensile Modulus | 3,600 MPa | 522,000 psi |
Elongation at Break | 30–50% | 30–50% |
Flexural Strength | 165 MPa | 24,000 psi |
Flexural Modulus | 3,700 MPa | 537,000 psi |
Compressive Strength | 120 MPa | 17,400 psi |
Izod Impact Strength (Notched) | 85 J/m | 1.6 ft-lb/in |
Hardness | Rockwell M99 | Rockwell R123 |
CHEMICAL RESISTANCE
Agent / Environment | Resistance Rating |
Strong Mineral Acids (H₂SO₄, HCl, HNO₃) | Good — consult for concentrated applications |
Weak Acids | Excellent |
Strong Alkalis / Bases | Good |
Weak Alkalis / Bases | Excellent |
Aliphatic Hydrocarbons | Excellent |
Aromatic Hydrocarbons | Excellent |
Halogenated Solvents | Excellent |
Ketones & Esters | Excellent |
Alcohols | Excellent |
Hot Water / Steam (to 200°C) | Excellent |
Fuels & Oils | Excellent |
Water Absorption (24 hr, ASTM D570) | < 0.5% |
ELECTRICAL PROPERTIES
Property | Value |
Dielectric Strength | 190 kV/m |
Dielectric Constant (1 MHz) | 3.2 |
Volume Resistivity | > 10¹⁶ Ω·cm |
TYPICAL APPLICATIONS
Note: RENU™ recycled powders are suitable for non-critical industrial, electronics, automotive, and commercial applications. They are NOT recommended for safety-critical aerospace structures or life-sustaining medical devices.
Application Area | Specific Uses |
Compression Molding | Preferred grade for press-and-sinter and direct compression molding — controlled flow aids part density |
Powder Coating | Suitable for powder coating applications where slower flow during cure is advantageous for thick or vertical surfaces |
Industrial Seals & Bearings | Seals, wear rings, thrust washers, and plain bearings in chemical processing equipment |
Non-Critical Medical Devices | Instrument housings and non-implant structural components requiring chemical resistance |
Electronics | Connectors, insulators, and carriers for high-temperature board-level assembly |
Automotive | Seals and valve components in high-temperature automotive powertrain systems |
PACKAGING & AVAILABILITY
Format | Details |
Box (Standard) | Up to 25 kg (55 lbs) per box — double-wall corrugated with poly liner |
Drum (Bulk) | 68 kg (150 lbs) bulk drums — fiber or plastic drum with sealed poly liner |
Custom Packaging | Available on request for larger volumes — contact PolyClean for details |
Labeling | Each container labeled with: RENU™ product code, mesh size, lot number, and date of manufacture |
Processing Notes LF grade is preferred for compression molding where HF grade may produce excessive flash at parting lines. Dry at 150°C for 3–4 hours before all melt-processing operations. Contact PolyClean for custom mesh sizes (20–170 mesh range available). |
DISCLAIMER The technical data contained in this document has not been produced by PolyClean Technologies through its own independent testing and measurements. This information has been assembled from publicly available data published by original polymer manufacturers and industry reference sources. PolyClean Technologies makes no warranties, expressed or implied, regarding the accuracy or completeness of this information. Customers are solely responsible for verifying that this material is suitable for their specific application. PolyClean Technologies shall not be liable for any damages resulting from the use of this information or from the use of its products in any application. This data is intended for general guidance only. RENU™ recycled materials are produced from post-industrial clean scrap and are appropriate for non-critical industrial, commercial, electronics, and general-purpose applications. They are not recommended or warranted for use in flight-critical aerospace structures, implantable medical devices, or other life-safety applications without thorough independent testing and qualification by the end user. |
RENU™ PEEK HF NAT-MP140 is a precision-milled, high-flow grade polyetheretherketone (PEEK) powder produced from clean, post-industrial recycled PEEK scrap. Ambient-temperature milling preserves the polymer’s molecular architecture, delivering thermal and mechanical properties that closely match virgin resin at substantially reduced cost. The 140-mesh cut (nominal 105 µm top size) is optimized for powder coating, selective laser sintering (SLS), compression molding, and thermal spray applications. The high-flow (HF) designation indicates this grade is derived from higher-viscosity PEEK feedstock milled to produce a freely-flowing powder suitable for broad industrial processing.
PHYSICAL PROPERTIES
Property | Value / Range |
Polymer Type | Polyetheretherketone (PEEK) |
Flow Grade | High Flow (HF) |
RENU™ Code | RENU™ PEEK HF NAT-MP140 |
Color | Natural (off-white to light tan) |
Mesh Size (US Standard Sieve) | 140 mesh |
Nominal Top Particle Size | ≤ 105 µm (microns) |
D50 Particle Size (typical) | 40–65 µm |
Particle Shape | Irregular (ambient milled) |
Bulk Density (loose) | 0.45–0.60 g/cm³ |
Apparent / Tap Density | 0.65–0.80 g/cm³ |
Moisture Content | < 0.05% (as-shipped) |
Recyclability | Post-industrial recycled content |
THERMAL PROPERTIES
Property | Value |
Glass Transition Temperature (Tg) | 143°C (289°F) |
Melting Point (Tm) | 343°C (649°F) |
Continuous Use Temperature | 250°C (482°F) |
Short-Term Peak Temperature | 310°C (590°F) |
Thermal Conductivity | 0.25 W/m·K |
Coefficient of Thermal Expansion (CTE) | 47 × 10⁻⁶ /°C |
Specific Heat Capacity | 0.32 cal/g·°C |
Heat Deflection Temperature (1.8 MPa) | 152°C (306°F) |
MECHANICAL PROPERTIES
Property | Value (SI) | Value (Imperial) |
Tensile Strength | 100 MPa | 14,500 psi |
Tensile Modulus (Young’s Modulus) | 3,600 MPa | 522,000 psi |
Elongation at Break | 30–50% | 30–50% |
Flexural Strength | 165 MPa | 24,000 psi |
Flexural Modulus | 3,700 MPa | 537,000 psi |
Compressive Strength | 120 MPa | 17,400 psi |
Izod Impact Strength (Notched) | 85 J/m | 1.6 ft-lb/in |
Hardness | Rockwell M99 | Rockwell R123 |
Coefficient of Friction (dry, vs steel) | 0.35–0.40 | 0.35–0.40 |
CHEMICAL RESISTANCE
Agent / Environment | Resistance Rating |
Strong Mineral Acids (H₂SO₄, HCl, HNO₃) | Good — consult for concentrated applications |
Weak Acids | Excellent |
Strong Alkalis / Bases | Good |
Weak Alkalis / Bases | Excellent |
Aliphatic Hydrocarbons | Excellent |
Aromatic Hydrocarbons | Excellent |
Halogenated Solvents | Excellent |
Ketones & Esters | Excellent |
Alcohols | Excellent |
Hot Water / Steam (to 200°C) | Excellent |
Fuels & Oils | Excellent |
Water Absorption (24 hr, ASTM D570) | < 0.5% |
ELECTRICAL PROPERTIES
Property | Value |
Dielectric Strength | 190 kV/m |
Dielectric Constant (1 MHz) | 3.2 |
Dissipation Factor (1 MHz) | 0.003 |
Volume Resistivity | > 10¹⁶ Ω·cm |
Surface Resistivity | > 10¹⁵ Ω/sq |
TYPICAL APPLICATIONS
Note: RENU™ recycled powders are suitable for non-critical industrial, electronics, automotive, and commercial applications. They are NOT recommended for safety-critical aerospace structures or life-sustaining medical devices.
Application Area | Specific Uses |
Powder Coating | Electrostatic and fluidized-bed powder coating of metal components for chemical resistance and high-temp service |
Additive Manufacturing (SLS/LS) | Selective laser sintering of functional prototypes and production parts for industrial and electronics applications |
Compression Molding | Near-net-shape production of seals, bushings, thrust washers, and valve components |
Thermal Spray | PEEK thermal spray coatings for anti-corrosion and electrical insulation on metal substrates |
Non-Critical Aerospace (structural) | Interior brackets, spacers, and non-load-bearing components where elevated temperature performance is required |
Non-Critical Medical Devices | Housings, enclosures, and non-implantable components requiring chemical resistance and sterilizability |
Electronics / Semiconductor | Wafer carriers, sockets, test fixtures, and insulators requiring high purity and dimensional stability |
Automotive | High-temp under-hood components, sensors, connectors, and fuel system parts |
PACKAGING & AVAILABILITY
Format | Details |
Box (Standard) | Up to 25 kg (55 lbs) per box — double-wall corrugated with poly liner |
Drum (Bulk) | 68 kg (150 lbs) bulk drums — fiber or plastic drum with sealed poly liner |
Custom Packaging | Available on request for larger volumes — contact PolyClean for details |
Labeling | Each container labeled with: RENU™ product code, mesh size, lot number, and date of manufacture |
Processing Notes Recommend drying at 150°C for 3–4 hours before processing to remove absorbed moisture. Melt processing: typical processing temperature range 360–400°C; avoid sustained exposure above 400°C to prevent degradation. For SLS applications, bed temperature is typically set 5–15°C below Tg (approximately 130–138°C). Contact PolyClean for custom mesh sizes (20–170 mesh range available). |
DISCLAIMER The technical data contained in this document has not been produced by PolyClean Technologies through its own independent testing and measurements. This information has been assembled from publicly available data published by original polymer manufacturers and industry reference sources. PolyClean Technologies makes no warranties, expressed or implied, regarding the accuracy or completeness of this information. Customers are solely responsible for verifying that this material is suitable for their specific application. PolyClean Technologies shall not be liable for any damages resulting from the use of this information or from the use of its products in any application. This data is intended for general guidance only. RENU™ recycled materials are produced from post-industrial clean scrap and are appropriate for non-critical industrial, commercial, electronics, and general-purpose applications. They are not recommended or warranted for use in flight-critical aerospace structures, implantable medical devices, or other life-safety applications without thorough independent testing and qualification by the end user. |
